RockShox Fork Servicing | Queenstown | NZ-Wide
RockShox 30 Fork Service New Zealand
Professional RockShox 30 Gold and 30 Silver servicing and repairs from our Queenstown suspension workshop. Service support depends on the exact generation, spring system, damper and availability of compatible parts.
Specialist Suspension Workshop
Fork servicing, repairs and setup completed in-house.
Fast Turnaround
Most suspension service work is completed within 24 to 48 hours where possible.
Six-Month Workmanship Warranty
CJSUSPENSION service workmanship is covered for six months.
NZ-Wide Service
Send your RockShox 30 to our Queenstown workshop from anywhere in New Zealand.
RockShox 30 Servicing
We service compatible RockShox 30 Gold and 30 Silver forks where the correct service parts are available. Each fork is inspected during servicing and we’ll contact you before carrying out any additional repairs or replacement work unless an additional-work allowance has been selected on the booking form.
25hr RockShox 30 Service
A lower leg and foam ring service to refresh lubrication between larger service intervals.
- Lower legs removed and cleaned
- Fork inspected for wear or damage
- Dust wipers cleaned and inspected
- Foam rings replaced
- Lower legs fitted onto the stanchions and lubrication oil renewed
- Foot studs torqued to factory specification
- Function checked
A quick maintenance service to keep the fork running smoothly between larger service intervals.
Book 25hr Service
50hr RockShox 30 Service
A mid-interval lower leg service to replace the dust wipers, refresh lubrication and keep the fork running smoothly between complete services.
- Lower legs removed and cleaned
- Fork inspected for wear or damage
- Dust wipers replaced
- Foam rings replaced
- Sag O-ring replaced
- Lower leg bushings checked for wear and play
- Lower legs fitted onto the stanchions and lubrication oil renewed
- Foot studs torqued to factory specification
- Function checked
A mid-interval service to renew the main lower leg wear components before the complete 100hr service.
Book 50hr Service
100hr RockShox 30 Service
A complete service covering the spring, damper and lower leg assemblies.
- Fork settings recorded
- Fork completely dismantled
- Fork inspected for wear or damage
- Lower leg bushings checked for wear and excessive play. If excessive wear or play is found, new bushings may be required
- Lower leg bushings sized and aligned to the upper crown steerer unit
- Air or coil spring fully serviced
- Damper fully serviced and vacuum-bled with new damper oil
- Damper seals, air seals, dust wipers, foam rings and sag O-ring replaced
- Grease and assembly lubrication renewed
- Lower legs fitted onto the stanchions and lubrication oil renewed
- Fork reassembled to factory torque specifications
- Settings returned to the original or recommended starting point
- Function checked
Our most comprehensive fork service, covering the spring, damper, lower legs and bushing alignment.
Book 100hr Service
RockShox 30 Repairs
Repair support depends on the exact RockShox 30 generation, damper and chassis specification. Older or uncommon versions are checked before additional work is approved.
RockShox 30 Damper Service
RockShox 30 damper servicing for removable drop-in cartridges that are poorly performing through compression, rebound or lockout control. Worn or failed seals, damaged bladders or worn internal parts can cause these issues.
- Damper removed and inspected
- Damper stripped and cleaned
- Service seals and wear items replaced as required
- Fresh damper oil added
- Damper rebuilt and torqued to specification
- Damper vacuum-bled if possible
- Adjuster function checked
If the complete damper cartridge can be removed as one unit, it can be sent separately for servicing and custom tuning can be added at the same time. If not, damper servicing must be completed as part of a 100hr fork service.
Book Damper Service
RockShox 30 Fork Scratch Repair
RockShox 30 stanchion scratch repair for suitable damage to improve the sealing surface and reduce further seal damage.
- Damage assessed before repair
- Damaged area cleaned and prepared
- Scratch filled with epoxy
- Repair left to cure for 24 hours
- Once cured, epoxy smoothed and finished
- Stanchion sealing surface checked before use
General wear is usually not suitable for this repair, as the epoxy needs a defined scratch to bond to. We’ll assess the damage first and advise whether repair or stanchion replacement is the best option.
Book Scratch Repair
RockShox 30 Steerer Tube Replacement
RockShox 30 steerer tube replacement for forks where the existing steerer is too short. Bent or loose steerers require an in-house CSU assessment first.
- Fork inspected for damage before work begins
- Existing steerer removed
- Steerer bore cleaned and prepared
- Special retaining compound applied
- New steerer pressed into place
- Installation checked after assembly
- Steerer supplied uncut for final fitment
If you plan to send only the CSU for steerer replacement, please note that we also require the lower legs and axle. This allows us to check lower leg bushing alignment before and after assembly to make sure everything is correctly aligned.
Book Steerer Replacement
RockShox 30 CSU De-Creak
RockShox 30 crown steerer units can develop creaking over time. We offer a service to eliminate the creak.
- Fork inspected for damage before work begins
- CSU inspected before work begins
- Lower leg bushing alignment checked before disassembly
- Crown steerer unit disassembled
- Surfaces cleaned and prepared
- Special retaining compound applied
- Professionally pressed back together
- Installation checked after assembly
- Lower leg bushing alignment checked after assembly
If you plan to send only the CSU for de-creak service, please note that we also require the lower legs and axle. This allows us to check lower leg bushing alignment before and after assembly to make sure everything is correctly aligned.
Book CSU De-Creak
RockShox 30 Removal & Installation From MTB
Removal and refitting of the RockShox 30 when a complete clean bike is delivered to the workshop.
- Suspension component removed from the bike
- Suspension component refitted after workshop service
- Basic installation checks completed
Complete bikes must arrive reasonably clean and ready to work on.
Book Workshop Service
Send Your RockShox 30 From Anywhere in New Zealand
Book online, complete the service form and courier your fork to our Queenstown workshop. Local riders can also drop off the fork or a complete clean bike.
RockShox 30 Service FAQs
Do you service RockShox 30 forks?
Yes. We service compatible RockShox 30 Gold and 30 Silver forks where the required service parts are available and the fork is in serviceable condition.
Are all RockShox 30 forks the same inside?
No. RockShox 30 forks were produced in air and coil versions with different dampers and chassis specifications, so the exact model and generation need to be confirmed before parts or repairs are approved.
Ready to Service Your RockShox 30?
Book your service online, complete the suspension service form, then either drop your fork into our Queenstown workshop or use one of the courier links on our booking page to arrange tracked shipping directly to us.